Service Mode (setup) of several TV click in the link of the mark

Procedure

 

To tune in pattern PHILIPS.

To adjust the tension of the net for 120 and 220 VAC.

Through the computer of fittings or remote control, to adjust the shine and the contrast until that the image is

totally dark.

To verify the voltímetro DC is with 130,5 ± 1V.

Adjust the shine and contrast again to obtain a current of 1,40 bad in the ammeter DC.

To confirm that the tension " hearter " is inside of 6,5 ± 0,24 Vrms.

 

C. PRE - FITTINGS OF THE CIRCUIT OF DEFLECION

 

C.1. Necessary instruments

Meter of high tension (strip of 50 KV).

Computer of fittings or remote control.

C.2. Connection

Meter of high tension.

(+) In the anode of CRT and (-) in the earth of CRT.

C.3. Fittings

To tune in pattern PHILIPS.

Adjustment R453 to correct the vertical height.

To tune in as pattern CROSSHATCH.

With the computer of fittings or remote control to adjust the shine and the contrast until that the image is

dark. To verify the discharge tension is of 29,25 KV ± 1,25% KV.

To tune in the pattern PHILIPS, and to readjust the shine and the contrast for normal image.

Using the adjustment computer or remote control to adjust the horizontal centralization

(CO) until that the image is centralized correctly.

To verify that the horizontal width is inside of the normal strip.

 

D. PRE ADJUSTS OF CAG

 

D.1. I score necessary

Osciloscópio

 

D.2. Connection

Osciloscópio:

(+) in the terminal TP47 and (-) in the earth

 

D.3. Fittings

To tune in pattern colored bars with sign level with 63 ± 2 dB (75W in open).

After confirming that the contrast is varied by the SUB-CONTRAST, to obtain a wave form in the osciloscópio

of 2,9 Vp-p. to maintain the pot. Of the contrast in the center.

Note: not to consider portion of Blanking.

To confirm that the sprinkle increases in the image when the pot. Of AGC RF (R 106) it is rotated in the sense antihorário.

Then slowly it rotates the same in the other sense until that the sprinkle disappears.

 

E. ADJUSTS PRELIMINARY OF WHITE IT BALANCES

 

E.1. Necessary instruments

Inspection / it adjusts of the reck with CRT, DY, CY, etc.

Adjustment computer or remote control.

Osciloscópio.

Jumper of short.

E.2. Connections

Inspection / it adjusts of the rack (Chassis).

Osciloscópio

(+) in TP35–GK or TP47G and (-) in the earth

Jumper of short: between TPs8 and earth (FA2)

E.3. Keys and Controls

Potenc. of Screen: totally in the counterclockwise sense.

Inspection / it adjusts of the rack: To adjust after the image to appear.

E.4. Adjustment of CUT OFF

To tune in pattern white balances.

Observe TP35 through the osciloscópio, soon after adjust the sub-shine (BO) for 2,4 VDC to be had,

as it represents below.

To observe GK through the osciloscópio, soon after adjust G-CUT OFF for it is had 195V, according to the

Ityou represents below.

Remove the tips of proof of the osciloscópio.

To adjust for G-CUT OFF same data for BLUE-CUT OFF.

To connect the jumper of short between TPS8 and earth, to obtain the horizontal line.

Rotate the screen potenciômetro slowly in the hourly sense until that the first color appears slightly.

To adjust RED-CUT OFF data and BLUE-CUT OFF, until obtaining the white line.

Remove the jumper of short.

 

 

F. TEST OF SOUND

 

To verify the sound varies proporcionalmente, working the volume controls.

2,4V

0V

195V

0V

F.1. Test of Operation of VR of Color

Pretion

Control of color center

Control of maximum contrast

Selector CATV Mode TV

 

Tests

To tune in colored bars and to confirm the colors in the image.

To confirm that the tint varies smoothly in the correct direction when the tint level is controlled.

To confirm that the color disappears with the color control at least and that the saturation of appropriate color is

obtained with the color control at the most.

To verify the saturation of color contrast, being varied the contrast controls.

 

G. ADJUSTS VCO

 

G.1. Necessary instruments

Generator of sign of 42,17 MHz

Freqüencímetro (100MHz)

Source of Feeding (16VDC)

Source of Feeding (1,5VDC)

Source of Feeding (2,5VDC)

Jumper capacitivo (1¼F)

G.2. Connections

Generator of sign of 42,17 MHz: (+) In the exit terminal IF of the selector; (-) In the earth of the selector.

Freqüencímetro: (+) In the terminal TP12; (-) In the earth.

Source of Feeding 1,5VDC: (+) in the terminal TP15; (-) in the earth.

Source of Feeding 16VDC: (+) in the terminal TP12; (-) in the earth.

Source of Feeding 2,5VDC: (+) in the terminal TP14; (-) in the earth.

Jumper capacitivo: (+) in the terminal TPA1; (-) in the earth.

G.3. Procedure

Adjust the generator of sign of 42,17 to obtain an exit of 100mVp-p.

Adjustment L105 until obtaining an indication of 3,58MHz ± 10%KHZ in the freqüencímetro.

Note: The adjustment of L105 should be made after a larger heating than 20 seconds.

 

 

H. PRE-AJUSTE OF AFT

 

H.1. Necessary instruments

Generator of 45,75MHZ ±100KHz variable.

Digital Voltímetro (DVM).

Jumper of short.

Source of Feeding 3,3VDC.

Source of Feeding 16VDC.

 

Source of Feeding 1,5VDC.

 

H.2. Connections

Generator of sign of 45,75MHz: (+) exit cable in the pin of the selector; (-) in the earth.

DVM: (+) in the terminal TP12; (-) in the earth.

Source of Feeding 3,3VDC: (+) in the terminal TP14; (-) in the earth.

0 Jumper of short: between TPS7 and the earth.

Source of Feeding 16VDC: (+) in the terminal TPD9; (-) in the earth.

Source of Feeding 1,5VDC: (+) in the terminal TP15; (-) in the earth.

 

H.3. Fittings

To adjust the exit of the generator of 45,75MHz in Mode to obtain tension of 1,7V ±0,1V in TP12.

To connect DVM in the terminal TP16 and to adjust L151 to obtain tension inside 4,6V ±0,5V.

To confirm that the tension in TP16 varies more than ±1V for the chaveamento of the sign generator of

45,75MHz in ±100KHz.

 

I. AJUSTES OF SIF

 

I.1. Necessary instruments

Osciloscópio.

Generator of sweeping of SIF.

Source of Feeding 3VDC.

Source of Feeding 16VDC.

 

I.2. Connections

Sweeping generator: (+) in the terminal TP21 the (-) in the screening of IF.

Osciloscópio: (+) of the entrance cable in the terminal TPA10; (-) in the earth.

Source of Feeding 3VDC: (+) in the terminal TP14; (-) in the earth.

Source of Feeding 16VDC: (+) in the terminal TPD9; (-) in the earth.

 

I.3. Fittings

To adjust the sweeping generator for 5,0Vp-p (75W in open, level non limited in the curve S).

To adjust L201 to obtain markers of ±150KHz in a lineal area.

To confirm that the level among the markers of ±150KHz surpasses 2,5Vp-p.

+ 150 KHz

- 150 KHz

Panasonic Model: CT-27SF24 CT-31XC24 CT-27XF34 CT-F2992

Chassis: GL 10C

 

With the linked television and using the remote control:

1) it selects SET-UP in the main menu and the modality CABLE in the option ANTENNA.

2) it selects TIMER and adjust the chronometer for 30.

3) it presses ACTION 2 times to leave of the menus and select the channel 124.

4) it adjusts the volume for the minimum. When pressing VOL - again, he/she will enter in the service Mode (CHK).

5) to leave it presses ACTION simultaneously and POWER for more than two seconds.

 

Panasonic Model: CT-215785 CT-315185

Chassis: AEDP242 NA6L

 

With the linked apparel, short-circuite the points FA1 and FA2. press ACTION (or MENU) and VOL+

simultaneously. Press POWER in CR to select the sub service menus. With CHANNEL + / -

select the item and with VOL + / - it adjusts the value. To leave it presses ACTION (or MENU) and POWER

simultaneously for two or three seconds

 

Panasonic Model: TAU

With the linked TV, adjust the volume for the minimum and place the screen OFF-TIMER in ON. Press RECALL

in the remote control and simultaneously VOL-na TV.

With the keys 1 and 2 it selects the adjustment Mode.

With the keys 3 and 4 choice the items.

With the key VOL + / - it adjusts the values.

 

Panasonic Model: European

To adjust the serious ones for the maximum and the sharp ones for the minimum. To press REVEAL at the same time in the control

remote and VOL - in the TV. With the teletexto keys RED and GREEN selects the item and with BLUE and

AMARILLA adjusts the values.

To leave NORM.

Mode of Service of TV Philco

Philco Chassi: PVT-2014 / Mode of Service

To place the volume at least.

" - " together with the key " 9 " of the remote control.

To press the key " 9 " to enter in other adjustment menus.

To use the keys 1 to the 8 of the remote control to select the fittings.

To conclude to press the key " 9 " first and at the same time the volume " -", soon after the key " 8" to leave

of the calibration.

 

Philco Chassi: 20V4 / Mode of Service

With the linked apparel it presses DISPLAY and MUTE.

To memorize: DISPLAY.

To leave: MUTE

 

Mode of Service of TV Philco

 

Philco Chassi: PSC-2976 / Mode of Service

 

 1-with the cable of force out of the electric outlet presses the key MEMU

 2 - it Ties the cable of force in the electric outlet, maintaining the key MENU pressed at least two seconds.

 3 - it Presses MMENU AND VOL + for more than two segundos  

 4 - it Presses POWER. The television will enter in Mode of Service

 5 -  to select the screens, use the keys CHANNEL + and CANAL  -

 6 -  to adjust, use the keys VOLUME + and VOLUME   -

 7 -  to leave the keys MENU AND POWER

 

Mode of Service of TV Philco

 

Philco Chassi: PCR-2049 / Mode of Service

 

 1-with the turned off television, press the keys CANAL +  and CHANNEL–at the same time

 2-loosen the keys and tie the cable of force in the electric outlet of CA

 3-await 30 seconds

 4-loosen the keys and press CHANNEL + to tie the television

 5-select the fittings with CHANNEL + and CHANNEL -; the values with VOL+ and VOL -

Mode of Service of TV Philco

Philco Chassi: CPH 06 / Mode of Service

 

 1-turn off the television in the general key

 2-press and maintain tight the key VOL + of the panel of the television

 3-tie the general key and await the image to appear (aproximadamente  30 seconds)

 4-after the image to appear, loosen the key VOL+ and soon after press VOL+ and VOL–at the same time

I  5-marry the service menu it is very big (expanded), press VOL again + and VOL–at the same time;

To select the fittings, use the keys CANAL+ and CHANNEL–
 

Mode of Service of TV Philco

Philco Chassi: TP–1452N / Mode of Service

 1-tie the cable of force in the electric outlet      
 2-install the antenna
 3-turn off the general key
 5-tie the general key (Power), staying with the key VOL + tight for approximately 30 seconds
 6-await to light the LED do  “Standy–by”
 7-tie the television and press VOL + and VOL–at the same time. And await to appear the service menu on the image
To leave, turn off the television.
 

Mode of Service of TV Philco

Philco Chassi: TP–1454 / Mode of Service

 1-turn off the cable of force of the electric outlet

 2-press VOL at the same time + and VOL - and tie the cable d it forces n atomada

 3-await until that enters the serviçi menu

 4-case the apparel enters in the Mode “Stand–by”, press CHANNEL + or call through the remote control.
 

Mode of Service of TV Philco

Philco Chassi: PCS–2956 / Mode of Service

 1-press the key VOL+ in the television

 2-work the key POWER; maintaining VOL + tight

 3-await the image to appear

 4-loosen VOL+ and press VOL at the same time + AND VOL–

 5-await to appear the service menu

 6-CHANNEL +  e CANAL - they make the selection and VOL + and VOL–the fittings

To leave, turn off the general key

 

Mode of Service of TV Philco

 

Philco Chassi: PCM–2051 / Mode of setup(Reset)

 

 1-tie the receiver in the electric net

 2-tie the antenna

 3-press the keys CHANNEL at the same time + and CHANNEL–in the television

 4-work the general key, maintaining pressed the keys CHANNEL + and CHANNEL–

 5-when Standy –by's LED lights it loosens the keys

 7-press VOLUME +

 8-press VOLUME ++

 9-await about 10 seconds, after the one that the memory will be “resetada”
 

Mode of Service of TV Philco

Philco Chassi: PVT–1412 / 2014 / Mode of Service

 

 1-adjust the volume control for the minimum
 2-press the key at the same time VOL - and the key 9 in the remote control
To change of screen, press the key 9 and VOL–
 

Mode of Service of TV Philips

Philips Chassi: GR1-VA 5 / Adjustment of Service

With the linked apparel, to terrify the pin 10 of the microprocessor IC7900 to put more than 2 seconds to that the screen

of the illustration below is presented, removing the connection soon after.

- Press the key to INSTALL and the next screen is below.

- Press the key again to INSTALL and to put last it will be the following screen.

Programming of the AND-EPROM

Press the key to INSTALL until appearing the screen of the previous illustration.

Through the keys CHANNEL (<) (>) it places the version of the apparel that should be:

14GL1015 0

14GL1316 41

20GL1045 0

20GL1346 41

After the programming it presses the key to INSTALL to put more than 2 seconds to memorize.

0 version: <41>

To install: To memorize

TMP47C834N TMP47C1237N

00:00 4

TMP47C834N

00:00:00 4

TMP47C1237N

Manual syntony?

<NOT YES>

TMP47C834N

04 close>

Menu: To select

TMP47C1237N

Memorization of standard PP and syntony of channels Tunes in any channel with antenna sign or

generator. Press the key MENU and in the sequence color adjustment, shine, contrast, volume for an image

normal and to put last he/she makes the memorization of PP.

Access the programming again terrifying the pin 10 of IC7900 and soon after press the key

To INSTALL to put more than 2 seconds to memorize.

channels VHF / UHF / Cable. In case it is not available, not

manual of the channels leaving the programming, in the normal Mode through the key

MENU.
 

Philips Chassi PT / Mode of Service

 

With the linked tv, type in the remote control:

062596 + menu, everything in sequence.
 

Philips Chassi GX / Reset

 

Place through the remote control the apparel in the channel 22 and soon after press the at the same time

keys in the apparel: -vol and + channel the screen will darken and again to light.

Philips Chassi GX–21 GX 1666/68

When the apparel is without the function [to INSTALL], in other words, inoperative, in the front panel, it is that because the same lost the access code for some reason, or fall of energy or even during the maintenance in the supported, in fact common of happening and without this function it is impossible to program the channels and many other important functions of fittings in the apparel.

So that the key to install it works again again, follow the steps below:

1-tie the apparel.

2-disconnect the antenna.

3-place in the channel 22, for the remote control.

4-press two keys simultaneously, [volume–and channel +],

Obs: Notice that the television had turned off and it had called alone again, soon after press the key to INSTALL again, and he/she will see that the functions came back your origins.

If in the case of these procedures they don't solve, turn off the television of the electric outlet and leave for exact 30 minutes turned off, after, come back the procedures above that with certainty had worked.

 

Philips Chassi Y6 / Mode of Service

 

With the linked apparel to press consecutively in the remote control the following keys: 0-6-2-5-9-6 -
MENU; he/she will appear in the screen the letter S and the identification of the equipment.

When pressing MENU again, they will appear the several adjustment items in groups of four; to select

use CHANNEL + / - and to adjust VOL + / -.

To leave it presses POWER and the data will be memorized.

 

Philips Chassis Anubis S / BB / DD / Mode of Service

 

Mode of check-up service:
I tan circuitar the terminals M28 and M29 while it ties the apparel. To leave it places in STAND-BY.

Mode of fittings:
I tan circuitar the terminals M31 and M32 while it ties the apparel; cursor the right selects data. Cursor
above or I lower it modifies value. To leave STAND-BY.
 

Philips Chassi L9. 2A / Mode of Service

 

 1)Press in the remote control the sequence of keys: 0 6 2 5 9 6 e  in seguida  MENU

 2)Na part superior of the screen will appear the indication SDM (Standard Mode of Service)

 3) to verify the content of the “buffer” of mistakes, press the key OSD in the remote control.

 4)Quando the television enters in the Mode SDM, LED will blink the number of times same to the value of the code of mistakes.

 5) to leave, place the television in “Standy–by”

 6) geometry fittings, place the apparel in the Mode SDM and press CANAL+ and channel–in the panel of the TV to the indication to appear SAM in the place of SDM.

 7)Selecione the options with the keys menu (upward or down). The entrance in each one of the items is made with the keys MENU (right and left). To leave, place the television in “standy –by”

 

Philips Chassis /Anúbis–he/she doesn't leave the demonstration Mode

 
In the case of the television, mainly the Model 20 GX 1895, to stay in the demonstration Mode, press CHANNEL at the same time +  e  VOLUME -  for the normal situation to come back
"BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 1pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 1pt; PADDING-BOTTOM: 1pt; BORDER-LEFT: windowtext 1pt solid; PADDING-TOP: 1pt; BORDER-BOTTOM: windowtext 1pt solid">

Philips Chassi GR - 6 / Mode of Service

 

 1)-press in sequence the keys: 0 6-2-5-9-6  Menu

It will be presented in the screen “NOID 9 :+MASKMIND  SAW: RT 5B; BANK 00; REGISTER 00 AND VALUE 00

 3)-THE Mode service understands 9 screens de  the juste:

 A-programming OF EPREOM

 B-Ajuste AFT

 C-adjustment of CAG

 D-level of entrance of MPX

Ityou  E-adjusts the setion of the audio channels

 F-setion stereo (solemnity)

 G-adjustment of white

 H-Geometria Horizontal  and Vertical

  I - Exit in the service Mode

 6)-select the items of the menu co m keys “UP” and DOWN.O selected item will be enhanced.

To activate or to disable the selected item, use the keys <and, as well as to alter the presented value

To leave, place the television in the Mode “stand –by”

 

Philips Chassi L01. 1L / Mode of Service

 

 1-type in the remote control the sequence 0 6 2 5 9 6 and soon after the key MENU

The possibility  2-exists of accessing the service Mode, short–circuitando the “jumper”963l and 9641

in the main panel, however we didn't advise this method

 3-Ao to be pressed OSD/STATUS  in the remote control, the content of the will be presented “buffer” of mistakes.

To leave of SDM, place the television in

 5-for geometry fittings, access SAM, typing the sequence 0 6 2 5 9 6 and soon after OSD / STATUS

 

Philips Chassi GL Several Models / Mode of Service

 

To  1-tie the television

To  2-select the options MENU in the television and at the same time to press the key MENU in the remote control to enter in the service Mode

To select the fittings it uses the keys CANAL+ and CHANNEL–

 4-  to adjust the selected values it uses the keys VOL + VOL–

 

Philips Model 21 PT 424 THE / Mode of Service

 

 1-remove the cable of force of the electric outlet

 2-call for a thread the pin 1 of EPROM 24C08 the earth

 3-insert the cable of force in the electric outlet and tie the television

 4-select the item wanted with the keys CHANNEL + AND CHANNEL–

 5-adjust the value wanted with the keys VOL+ and VOL–

To leave in the service Mode, turn off for the remote control and remove the cable of force of the electric outlet.

 

Philips Model 29 PT 752 / 78 BR / Mode of Service

 

 1-Interligue the “jumpers” 9040 and 9041

 2-tie the television for the general key

 3-THE screen will present a green rectangle with the indication SDM

 4-after accessing the Mode SDM, remove the short–circuit among the “jumpers” 9040 and 9041

 5-press in the television  VOL + and VOL -, for approximately 3 seconds

 6-knot place of SDM, will appear the indication SAM.

 7-choose the wanted item it uses the keypad  UP and DOWN

To adjust the selected value it uses the keypad  LEFT and RIGHT

To come back to the main menu, press the key MENU

To leave in the service Mode and to memorize the fittings it presses the key POWER  in the remote control . 

Mode of Service of TV Precision / Orion

Precision / Orion Model: All

With the linked TV without OSD to press the occult key in the remote control. Some Models have a hole in the

it covers and others have to disaswithoutble CR to have access to the button

 

Mode of Service of TV Precision / First-Line

 

Precision / First-Line Chassi: AK 19

1-knot remote control presses MENU and enter in INSTALLING.

2-introduce the sequence 4-7-2-5.

To select: CHANNEL + / -.

To adjust: VOL + / -.

To save: Red button.

To leave: TV

 

Precision / First-Line Chassi: AK 20

1-knot television presses VOL - and in the remote control the sequence PROG, -, TV.

To select: CHANNEL + / -.

To adjust: VOL + / -.

To save: Red button.

To leave: TV

 

Mode of Service of TV Quasar

Quasar Model: SP2726K SP2736K SP3136

Chassis: AREDC224 AEDC242

 

With the apparel linked, short circuite the points FA1 and FA2. press ACTION (or MENU) and VOL+

simultaneously. Press POWER in CR to select the sub service menus. With CHANNEL + / -

select the item and with VOL + / - it adjusts the value. To leave it presses ACTION (or MENU) and POWER

simultaneously for two or three seconds.

 

Quasar Chassi: AK 20

 

In the television it presses VOL - and in the remote control the sequence PROG, -, TV.

To select: CHANNEL + / -.

To adjust: VOL + / -.

To save: Red button.

To leave: TV
 

Mode of Service of TV RCA / GE / Proscan

 

RCA / GE / Proscan Chassi: CTC175 CTC176 CTC177 CTC186 CTC187

With the linked apparel, press and maintain the button MENU while it presses successively POWER and

VOL +.

He/she will appear in the screen P00 and V00. press VOL + until that indicates V76 and, then, pressing CH + / -, select the

items and VOL + / - the level of the same ones. For salts saving the data: POWER.

Attention: The item P01 is the horizontal frequency and if it be lowered too much it dismantles the television.

 

RCA / GE / Proscan Model: RAR2050 RAR2150 GE-20091

Chassis: TX-91

With the linked apparel, press and maintain the button MENU while it presses successively POWER and

VOL +.

The screen will show P000 and V000. press VOL + until that indicates V076, V077, V078 or V079 in agreement with the

that one want to adjust.

CH + / - it selects.

VOL + / - it adjusts.

To leave: POWER.
 

Mode of Service of TV Samsung

 

Samsung Chassi: KCT52A / Mode of Service

 

Substitution of EEPROM (IC902)

In the substitution of whole EEPROM the data of fittings return to the initial values being necessary to reprogram these data

After substituting IC902. To heat up the apparel for some seconds.

In the case of change of the kinescope–to adjust purity and convergence.

 Adjust:
1. I balance of white–White Balances
2. Sub-shine–Sub-Brightness
3. Vertical centralization–Vertical Center
4. Vertical height–Vertical Size
5. Horizontal width–Horizontal Size
6. NS
 

ENTERING IN THE MODO SERVICE

 

1. To enter in MOD SERVICE–it uses the remote control, pressing the following commands:

STAND-BY–MUTE –1–8–2 - POWER ON

2. It will be presented the screen " FACTORY Mode " that possesses 04 areas:

ADJUSTMENT (Fittings)

TEST PATTERN (Pattern of Tests)

SET OPTION BYTE (Bytes of option of fittings)

FACTORT RESET (factory Reset)

1. Access the Mode of fittings pressing the keys of " VOLUME ". The meters of fittings are

CHANNEL ".

2. After completing MODO SERVICE " fittings to turn off the television in the POWER OFF.

FITTINGS: ADJUSTMENT - TABLE.

AGC 45 NHS 42

VCO 64 NEA 44

SBT 9 NEP 27

SCT 2 NEC 31

SCR 11 NET 31

STT 11 PSL 20

ID 34 PVS 32

GG 32 PVA33

BG 34 PVA 33

SCO 9 PEA 43

NSL 21 PEP 31

NVS 25 PEC 22

NVA 40 PET 28

METER OF MAIN FITTINGS

Note: The values of data ends are worth in agreement with the Model

N... System NTSC, PAL-M

P... System PAL-N

Examples:

NSL–Vertical Slope (vertical ramp) in the system - PAL-M and NTSC

PSL - Vertical slope - (vertical ramp) in the system–PAL-N

Pattern of Test:

This Mode can be used to confirm the convergence fittings and purity they are right.

Access the meters of the PATTERN OF TESTS pressing the keys of CHANNELS, while the Mode

SERVICE is in ON. The courses of it will move for the pattern tests. Press the key of VOLUME then. In the

screen will appear

RED

GREEN

BLUE

SET OPTION BYTE (byte of adjustment option)

In the Mode SERVICE, several options can be selected like " Option Byte "

Example:

BYTE 1: 00 (initial language in Portuguese)

BYTE 1: 01 (initial language in Spanish)

OPTION BYTE 0

0 0: NONE COMB FILTER

1: COMB FILTER

1 0: PORTUGUESE

1: SPANISH

0 2 0: TV/VIDEO 1/VIDEO 2

(HEX) 1: VIDEO 2 ONLY

3 0: SOLEMNITY POWER ON

1: NONE AUTO POWER

0 0: SHARPNES CONTROL

1: SHARP. LINEAL CONTR.

1 0: NTSC/PAL-M/PAL-N

0 1: NTSC / PAL-M

(HEX) 2 0: NR

1: NONE NR

3 DON'T CARE

DON'T CARE

FACTORY RESET:

When " Factory Reset

control of use they are available in the MENU (picture, sound, and other functions)

Note: When Factory Reset is selected the data of fittings in the MODO SERVICE they cannot be

modified.

FUNCTION OSD SCREECHES DATE

SOLEMNITY GAIN CONTROL AGC 0 ~ 63 43

VOLTAGE CONTROL OSCILLATOR VCO 0 ~127 64

SUB BRIGHT SBT 0 ~ 13 5

SUB CONTRAST SCT 0 ~1 3 10

SUB COLOR SCR 0 ~ 13 8

SUB TINT STT 0 ~ 13 2

RED GAIN ID 0 ~ 63 32

GREEN GAIN GG 0 ~ 63 32

BLUE GAIN BG 0 ~ 63 32

S–CORRECTION SCO 0 ~ 63 9

VERTICAL SLOPE NSL,PSL 0 ~ 63 25

VERTICAL SHIFT NVS,PVS 0 ~ 63 32

VERTICAL WIDTH NVA,PVA 0 ~ 63 22

HORIZONTAL SHIFT NHS,PNS 0 ~ 63 38

EAST WEST AMPLITUDEN NEA,PEA 0 ~ 63 53

EAST WEST PIN NEP,PEP 0 ~ 63 42

EAST WEST CORNER NEC,PEC 0 ~ 63 31

EAST WEST TILT NRT,PET 0 ~ 63 31

 

Samsung Model: CN-3338 / CN-5038 AND 39   / CN-5066V

Chassis: K1

With the turned off television, press in the remote control: MUTE, 1, 8, 2 and POWER to enter in the main menu of service.

To choose a sub menu uses CHANNEL + / -.

To alter it uses VOL + / -.

To return to the main menu it presses MENU.

To leave and to save it presses POWER.

 

SAMSUNG CHASSIS KCT 52 –CN 5038 V

 

        Através of the remote control, with the television in Standy –by, press:

        1)-MUTE -1–8–2 AND POWER ON

        2)Será presented the screen “Factory Mode”, with 4 areas:

           -  ADJUSTMENT

           -  TEST PATTERN

           -   Set Option Byte

           -   FACTORY RESET

        4) to select the items it uses the keys CHANNEL + and CHANNEL–

        5) to leave in the service Mode, turn off the television in the key POWER ON.

Samsung Model: CX3079

 

Inside of the remote control it is not suitable a diode installed. Place a 1N4148 or similar in the place,

turn on the TV and press MENU to enter in the service Mode.

Samsung Model: CW593

With the apparel in stand-by, press the following sequence of keys: DISPLAY, MENU, MUTE, POWER.

With CH + / - it selects the item.

With VOL + / - it adjusts the value.


 

Samsung Model: PLH-403 (Projetor LCD)

With the turned off apparel, press the following sequence in CR: MUTE, 1, 8, 2, POWER. With VOL + / -
navigate in the menu and with MENU and MUTE it changes the data.
Press MEMORY to save and DELETE to leave.
 

Mode of Service of TV Sanyo

Sanyo Model: C20LB94M

Chassis: LA-4A

 

To maintain pressed the button MENU in the TV and to press the button 2 in the remote control.

To adjust the fine syntony, to maintain pressed the button MENU in the TV and to press MENU in the remote control.

With the linked apparel, press M (memory) in the TV for two seconds and immediately M in the control

remote.

Press SOUND to choose and VOL + / - to adjust.

 

Mode of Service of TV Semp Toshiba

 

Toshiba Chassi: U9 / Mode of Service

 

The fittings should only be made with remote controls that contain the functions MUTE and CALL      

        2)Press again MUTE and maintaining her compressed, press the key menu in the panel of the television.

        3)Deverá to appear the letter S  in the song superior right of the screen.

        4)Os addresses and adjustment data appear in the left superior song of the screen

        5)Os addresses are selected with keys CH + and CH–of the remote control.

        6)Ajustes the data with as  keys VOL + and VOL–

        7) to leave in the Mode of services, turn off and tie the television again

 

Mode of Service (S)

 

Press the key mute in the remote control and observe the registration " sound turned off in the screen " of the tv.

Press the key again MUTE and maintaining her pressed it works the key MENU in the panel of the television.

The letter " S " appears in the song superior right of the screen.

The addresses and data appear in the left superior song of the screen. The addresses are worked with the

keys CH + / - of the remote control and the data with it types them VOL + / -

 

Mode of Development (D)

 

With the television in the Mode S presses the key CALL in the remote control, and maintaining her pressed it works the

key MENU in the panel of the television

Observation: to leave in the Mode of Service or in the Mode of Development it turns off and tie him/it again

television.

Reset:

The television should be in Mode of Service

Press the key CALL of the remote control

Press the key CALL in the remote control and without you liberate her it presses the key CH + in the panel of the television.

 

TOSHIBA CHASSI U–11 AND U–14

 

      The fittings should only be made with remote controls that contain all as  options (“complete”)

 

        1)Press in the remote control the key MUTE, until the message TURNED OFF SOUND to appear

        2)Press again MUTE and press MENU at the same time in the painel  of the television .Nos Models in that the key MENU not to exist, press VOL at the same time + and VOL -) Models with suffix FAV)

        3)Aguarde until appearing the indication S in the superior song of the screen

        4) The addresses and data appear in the left superior song.

        5)os addresses are selected by the keys CH + and CH–in the remote control

        6) to adjust the data, use the keys VOL + and VOL–

        7) to leave in the service Mode, turn off the television and call–again

Toshiba

Chassis: TAC9700 TAC9702 TAC9727 TAC9800 TAC9803

 

With the linked television it presses MUTE in the remote control, loosen and press again while it presses MENU

in the television; he/she will appear a S in the screen. Press MENU again to enter. With CHANNEL + / - it selects the

items and with VOL + / - the values. To leave: POWER.

 

Toshiba Model: MV13K… MV19K… (COMBOS TV / VHS)

 

Turn off the apparel of the electric outlet for enough time to turn off the programming of the clock. Tie the television

and press VOL - while it presses in the remote control: 9 for fittings or 2 for adjustment H of OSD.

 

Mode of Service of TV Sharp

 

Sharp Chassi: All / Mode of Service

 

Hold the key pressed power and place her/it in the electric outlet, only loosen key after the apparel to call.

To leave in the service Mode, press the key to leave of CR and turn off her/it for CR.

 

Sharp Chassi: C-29ST54

 

Mode SERVICE OF THE TV SHARP Model C-29ST54

1. To enter in the MODO SERVIÇO:

1.1 Mode SERVICE–SWEEPING–COLOR–RB - AGC...

To locate the points of test PT 2001 and PT 2002 (it is close of the Microprocessor)

With the linked apparel, preferably in the channel AV, jumpear quickly (a small touch) PT2001 with PT2002.

In the first touch he/she will appear the positions of S0... until... S19, that can be altered by the keys of channels + and–

The addresses the values will be altered by the keys volume + and–

To observe the values below in the table:

OBS.: take very care (to appear the digits M0–it adjusts of the sound). Make the jumpeamento again until coming back in the digits S0... S19.

 

1.2 Mode SERVICE - SOUND

 

Repeat the procedures above, they put with the digits M0... even M6

To Leave again in the Mode SERVICE jumpear (quickly for some seconds) until disappearing the

digits of S0 and M0

 

ItYOU CONTROLS OF THE ADDRESSES AND VALUES

 

FUNCTION       ENDEREÇO       VALOR

SUBCONT      S01 56 M01          26

TINT                 S02 46 M02          1E

SUBCOR        S03 36 M03          1B

SUBRILHO     S04 4C M04         16

NITIDEZ          S05 24 M05          3B

FREQ/VERT  S06 00 M06          25

POS.HOR       S07                        11

AGC                SO8                       24

ALTURA         S09                        26

                         S10                        2F

(RGB)R           S11                        00

(RGB)G           S12                       11

(RGB)B           S13                        06

G DRIVER      S14                        7F

B DRIVER      S15                        80

3,58                 S16                        00

BALANCE      S17                       20

CLAMP           S18                       17

                         S19                        BF

 

Sharp Model: 25K-M180 25K-100 CK25M10 CK25SR

 

Disconnect the TV of the electric outlet and press CANAL+ and VOL + together while it ties the apparel.

To select: CHANNEL + AND CHANNEL -.

To adjust: VOL + AND VOL -.

To leave it presses POWER or disconnect the apparel of the net

 

Sharp Model: 25G-M60 25G-S60

Chassis: SN-51

 

Seek close to IC 2001 (or IC001) the points TP2001 and TP2002. Apply a short momentary circuit among them.

To select: CHANNEL + AND CHANNEL -.

To adjust: VOL + AND VOL -.

To leave it presses POWER or disconnect the apparel of the net.

 

Sharp Model: 63CS-03SN 63CS-05SN

 

With the turned off general switch, press and maintain the keys CHANNEL + and VOL + while it ties the apparel.

Ityou will appear the service screen.

CHANNEL + / -: Select.

VOL + / -: Adjust.

To save the new data, press STAND-BY in the remote control.

To leave it turns off the main switch.

 

 Modo of ServiçoTV Sharp

 

Sharp Chassi: C–1457 / 2057

 

After making the syntony automática,  after tuning in a certain channel, when moving for another channel the image he/she flees.

1 - it tunes in channel any

2 - it turns off the television

3 - he/she enters in the Mode of Service

4 - it presses 100 in the remote control

5 - in case he/she appears the error message, await some minutes

6 - it turns to press 100 in the remote control

7-  Repeat the steps 5 and 6 until the message to appear in the tela  OK

 

 Modo of ServiçoTV Sharp

 

Sharp Chassi: C - 29ST98 / C-1457

 

        1)Retire the cable of force of the electric outlet, tuning in the channel 3 or 4 before

        2)Press the key POWER of the panel and insert the cable of force again in the electric outlet

        3)Aguarde the television to call–if automáticamente

        4)Por middle das  numeric keys and AMI, SLEEP, to REVIEW and MUTE of the remote accesses the wanted fittings.

        5) to adjust it uses the keys CH + and CH -

        6)A key 2 adjusts the linearidade and the key 3 the height.

        7) Made the fittings, press to LEAVE and turn off the television through the remote control.

Mode of Service of TV Sony

 

Sony Chassi: All / Mode of Service

 

Electric fittings for the remote control

1 - access method to the service Mode

the) - the television must it is in stand-by (turned off by the Power off)

b) - it Presses the following sequence of keys in the remote control:

Display> 5> volume (+)> Power THE time for the sequence is of 2 seconds

c) - After the television it will call and to appear in the screen the message SERVICE soon lowers writing the item and the function.

 

and) - it presses the button 3 or 6 of the remote control to change the function.

f) -  to record in the memory it presses the buttons MUTING and ENTER

g) - it Presses the button 8 and ENTER for reinicializar.

h) -  to leave in the Mode of SERVICE it turns off the apparel, and call again again.

2 - to confirm the Recording in the memory

the) - After the adjustment it turns off the apparel of the electric outlet of force, and await some minutes and tie the again

electric outlet..

b) - it Ties the apparel again in Mode service and it is verified the values they are in agreement with the values

 

in the list to follow the item to be adjusted.

 

 

Sony chassis: NANNY-4B

Models KV-21B80 and KV 21S85

 

A. TAKEN CARE AND PRECAUTIONS

 

A.1. Care!

I tan circuite the ANODE of the image tube and it castrates him/it of the anode in the metal chassis, screening of CRT, or

in the painted carbon in CRT, before removing the ANODE.

 

A.2. Precautions!!

An isolação transformer can be used during some service to avoid a possible shock

electric, due to the chassis to be alive. The chassis of this receiver are directly connected with the

feeding line AC.

 

A.3. Cares with the components related with the safety!!

 

For replacement, use pieces alModes recommended by the manual or published supplement

by Sony. The circuit fittings that are critical for us to operate in safety they are

identified in this manual. AlModes follow these procedures when it will substitute

critical components or if he/she has suspicion of inappropriate operation.

 

B. FUNCTION OF SOLEMNITY-DIAGNOSIS

 

The apparel of this manual possesses the solemnity-diagnosis function. To happen some fails:

 

 Caso the symptom of the mistake cannot be reproduced, use the remote control to access the memory where the data of defects are stored for reveros happened problems and your frequency.

 

B.1. Indicators of the test of the diagnosis

When it happens a mistake, the led STANDBY/TIMER it blinks the number of times adjusted to indicate the cause

probable of the problem. To happen more than a mistake, the led will indicate the first problem.

The Result of all the solemnity-diagnoses will be suitable in the visor. Not having flaws, the self-diagnosis visor

Ityou will indicate the value " 0 ".

 

Description of the Item of the Diagnóstico N.º of times in that the led STANDBY/TIMER blinks Screen of SELF-DIAGNOSIS.

 

Result of the Diagnóstico Localização of the Cause Probable Detected Symptoms

* Apparel doesn't call

Ityou doesn't light----------- THE cable of force is turned off.

- Fuse is burned (F600).

- The apparel doesn't call.

- The TV is not fed.

- Tension lack CA.

* Sobrecorrente

in the linha+B

(OPC)

2 times 2:0 or 2:1

- H.OUT (Q502) with escape. (Plate THE).

- Q701 with escape. (Plate C)

- The apparel doesn't call.

- Escape in the feeding.

* Lack of Vertical DEFLECION

4 times 4:0 or 4:1 - +13V are not supplied. (Plate THE)

- IC541 with escape. (Plate THE)

- He/she entered in Mode standby after horizon raster.

- It lacks of pulse of Vertical DEFLECION.

- The feeding is in short or the feeding stopped.

* It fails in the sign White it balances (not balanced)

5 times 5:0 or 5:1

- Video OUT (Q392 for 394) with escape. (Plate THE)

- IC301 with escape. (Plate THE)

- G2 is adjusted inadequately.

- No raster was generated.

- The exit of pulse of reference of the average DEFLECION of the CRT cathode is small.

Note 1: If an overload +B be detected, the broqueio of the vertical DEFLECION is detected simultaneously.

The symptom diagnosed first by the microprocessor it will be indicated in the screen.

 

B.2. For the indication Standby to stop blinking

Turn off the key of feeding of the main unit of the TV or disconnect the cable of feeding of the electric outlet

of the electric net for the indication STANDBY to stop blinking.

 

B.3. Screen of SOLEMNITY-DIAGNOSIS

For mistakes with symptoms as " the feeding sometimes " turns off or " the screen disappears some

times " which they cannot be confirmed, are possible to review the last occurrences of the flaws

to confirm this screen.

 

To enter in the Screen of Test

 

In the Mode STANDBY, press sequencialmente the keys to proceed quickly in the remote control

as to proceed:

 

Solemnity-diagnosis screen:

Screen Channel 5 Volume - Power ON

SOLEMNITY DIAGNOSIS

2: 0

3: N/A

4: 0

5: 1

101: N/A

The number " 0 " indicates that was not detected flaws.

The number " 1 " indicates that the flaw was only detected once.

 

B.4. Circuits involved in the SOLEMNITY-DIAGNOSIS

SOBRECORRENTE +B (CP)

Ityou happens when a sobrecorrente in the line +B (115V) it be detected by the pin 18 of IC301. If the

voltage of the Pin 18 of IC301 goes smaller than 1V when V. SYNC goes larger than seven vertical

in a period, the equipment will turn off automatically.

Flaw of Vertical flexão

It happens when there is not vertical DEFLECION in the pin 17 of IC001. The feeding will be turned off when the

interval of the waves to exceed to 2 seconds.

Flaw of White Balances

If the level RGB (he/she refers the level RGB of the detector AKB Ref of the pulse that detects 1K), not to adjust in 2

seconds after the apparel to be called, this mistake will be detected by IC301. The TV will stay

linked, but there won't be image.

 

B.5. Method of adjustment in the Mode of service adjustment

Procedure in the Mode of service adjustment

1. Mode Standby. (turned off)

2. DISPLAY 5 VOL (+) POWER in the remote control.

(Press each key inside of one second.)

 

Entrance in the Mode of service adjustment

 

3. The screen shows the item to be adjusted.

4. Press 1 or 4 in the remote control to select the item.

5. Press 3 or 6 in the remote control to change the data.

6. Press MUTING later ENTER to write in the memory.

SERVICE AFC 0         

Disp

(item)

Item

date

 

Memory in the Mode of service adjustment

 

7. Turn off and call the apparel to leave.

B.6. Adjustment of White Balances

1. Place a sign of white screen.

2. Enter in the Mode of SERVICE.

3. Adjustment DCOL for " 0 ".

4. Adjust the CONTRAST and SHINE at least.

5. Adjust with SBRT if necessary.

6. Select GCUT and BCUT with 1 and 4.

7. Adjust the best swinging of the white with 3 and 6.

8. Adjust the CONTRAST and SHINE at the most.

9. Select GDRV and BDRV with 1 and 4.

10. Adjust the best swinging of the white with 3 and 6.

11. Reset DCOL for " 1 ".

12. Write in the memory pressing MUTING and ENTER.

 

C. ADJUSTS OF THE CIRCUITS

 

C.1. Procedure in the Mode of Adjustment of Service

1. Mode Standby. (turned off)

2. DISPLAY 5 VOL (+) POWER in the remote control.

(Press each key inside of one second.)

 

Entrance in the Mode of Adjustment of Service

 

3. The screen shows the item to be adjusted.

4. Press 1 and 4 in the remote control to select the item.

5. Press 3 and 6 in the remote control to change the die.

6. Press MUTING later ENTER to write in the memory.

SERVICE WRITE MUTING (green)

ENTER (red)

SERVICE SYS 0

Disp

(item)

Item

date

Memory in the Mode of Adjustment of Service

 

7. Press 8 later ENTER in the remote control to initialize.

8. Turn off and call the apparel to leave.

 

Method of confirmation of the Writing in the Memory

 

1. After the adjustment, disconnect the plugue of the electric outlet AC of the electric net, and later connect again in the

electric outlet AC.

2. Tie the feeding and adjustment in the service Mode.

3. Call the adjustment items again to confirm if they are adjusted.

 

Keys of Adjustment and Indicator

 

 

ENTER (red)

SERVICE RESET

Accomplish the step 7 when it adjusts Ids 0 for 4 and when substitutes and to adjust IC003

 

Items of Adjustment

 

NO. ITEM FUNCTION STRIP OF DATA

NTSC PAL-M PAL-N VÍDEO MÉDIA OF DATOS

1 HSIZ Horizontal Width 0-63 31 31 31 31

2 HPOS Horizontal Position 0-63 21 21 19 34

3 VBOW VCT LINE BOWING ADJ. 0-15 6 7

4 VANG VRT LINE BOW SLANT ADJ. 0-15 6 7

5 TRAP Horizontal Trapeze 0-15 15 7

6 PAMP HORIZ. Pin Distortion Adj. 0-63 31 31 31 26

7 CPIN Same Pamp-SCRN TP/BTM 0-63 31 31 31 31

8 VSIZ Vertical Height 0-63 43 43 47 12

9 VPOS Vertical Position 0-63 35 35 28 13

10 VLIN Vertical Linearidade 0-15 7 7 7 7

11 Vertical SCOR Amount Adj. 0-15 7 7 7 4

12 VZOM 16:9 CRT Z Mode ON/OFF 0,1 0 0

13 EHT Correction of high voltage VRT 0-15 15 7

14 ASP ASPECT RATIO CONTROL 0-63 47 47

15 SCRL 16:9 CRT Z Mode TRAN SCRL 0-63 31 31

16 HBLK RGB OUT WIDTH CONTROL 0,1 1 0

17 LBLK LEFT SCREEN HBLK CONTROL 0-15 15 7

18 RBLK RGT SCREEN HBLK CONTROL 0-15 3 7

19 VUSN V SAW Waveform Buy 0,1 0 0

20 HDW H. Drive Presses Width 0,1 0 0

21 EWDC EW/DC ADJUST 0,1 0 0

22 LVLN SCREEN BTM VRT LIN ADJUST 0-15 0 0

23 UVLN SCREEN TOP VRT LIN ADJUST 0-15 0 0

24 RDRV exit Control R 0-63 30 31

25 GDRV exit Control G 0-65 24 31

26 BDRV exit Control B 0-63 21 31

27 RCUT Controle of exit of the cut R 0-15 15 7

28 GCUT Controle of exit of the cut G 0-15 7 7

29 BCUT Controle of exit of the cut B 0-15 7 7

30 DCOL ON/OFF Dynamic Color 0,1 0 1

31 SHUE SUB HUE 0-31 15 7

32 SCOL SUB COLOR 0-31 14 14 14 7

33 SBRT Shine 0-31 7 8

34 RON ON/OFF of exit of R 0,1 1 1

35 GON ON/OFF of exit of G 0,1 1 1

36 BON ON/OFF of exit of B 0,1 1 1

37 AXPL Áxis PAL 0,1 0 0

38 AXNT Áxis NTSC 0,1 0 0

39 CBPF CHROMA BPF ON/OFF 0,1 1 1

40 CTRP Y TRAP FILTER ON/OFF 0,1 1 0 0

41 COFF COLOR ON/OFF 0,1 0 0

42 KOFF SET COLOR KILLER 0,1 0 0

43 SSHP SUB SHARPNESS 0-15 10 8

44 SHPF SHARPNESS CIRCUIT FO 0,1 1 1 1

45 PREL PRE/OVR SHOOT SWITCHING 0,1 0 0

46 Y-DC DC Trans Ratio Switching 0,1 1 1

47 GAMM GAMMA CORRECTION AMNT 0-3 1 2

48 ABLM Mode CHAVEAMENTO ABL 0,1 7 0

49 VTH ABL C D VTH SWITCHING 0,1 1 1

50 YDEL Controls of the time of Delay Y 0-15 7 7

51 NCOL In Color ID 0,1 1 0

52 FSC FSC OUT ON/OFF 0,1 1 0

53 K-ID KILLER ID CONTROL SW 0,1 0 0

54 HOSC H VCO OSCILLATION FREQ. 0-15 10 8

55 VSS V SYNC SLICE LEVEL 0,1 0 0

56 HSS H SYNC SLICE LEVEL 0,1 0 0

57 HMSK 0,1 1 1

58 VTMS SELECT SIGNAL VTIM PIN 0-3 0 0

59 CDMD V CNT DWN Mode SWITCHING 0-3 0 1 1

60 AFC AFC LOOP GAIN SWITCHING 0-3 0 0 0

61 FIFR FIELD FREQUENCY 0-3 3 1

62 SBAL Sub it Balances 0-15 13 7

63 SBAS Sub Bass 0-127 15 20

64 STRE Sub Treble 0-63 51 3

 

Table ID

 

KV - ID-0 ID-1 ID-2 ID-3 ID-4

1 21B80 19 3 2 14 117

2 21S85 19 3 5 206 117

 

C.2. Fittings of the Plate

 

Adjustment of the Horizontal Frequency

1. Insert a sign of the monoscópio.

2. Enter in the Mode of Adjustment of Service.

 

4. Select the item of AFC, adjustment in the level 3 (free).

5. Verify the horizontal frequency for 15735 ± 200 Hz. (NTSC) or verify the

horizontal frequency for 15650 ± 200 Hz. (Trinorma).

6. Select the item of AFC again, adjust the level " 0 ".

7. Write in the memory pressing MUTING later ENTER.

 

Adjustment of the Vertical Frequency

1. Select video 1 without entrance sign.

2. Adjust the conditions with the standard adjustment.

6 connector and earth.

4. Verify the Vertical Frequency for 60 ± 2 Hz (NTSC).

5. Verify the Vertical Frequency for 50 ± 2 Hz (Trinorma).

 

Adjust of the Sub Contrast (SCON)

1. Insert a sign of color bar.

2. Select the red color.

3. Adjust for the Mode of SERVICE.

4. Select the item DCOL for the level " 0 ".

5. Adjust the conditions as to proceed.

Contrast…………………… Max

Color…………………………… Min

I shine………………………… Center

R ON………………………… ON (1)

G ON………………………… OFF (0)

B ON………………………… OFF (0)

SERVICE RON 1

1: ON

0: OFF

6. Connect the tip of the osciloscópio in the Pin CN301 5 (R OUT) of the plate C and earth.

7. Select RDRV with 1 and 4.

8. Adjust with 3 and 6 for: 1.70 ± 0.05 VP-P.

9. Reset the item DCOL for the level " 1 ".

10. Write in the memory pressing MUTING later ENTER.

11. Come back the items to proceed for normal after the adjustment.

Contrast…………………… Max

Color…………………………… Center

I shine………………………… Center

R ONON

G ON………………………… ON

B ON………………………… ON

 

Adjustment of the Position of the Characters (DISP)

1. Insert a sign of color bar.

2. Enter in the Mode of SERVICE.

3. Select DISP with 1 and 4.

4. Adjust with 3 and 6 to adjust the characters in the center.

5. Write in the memory pressing MUTING later ENTER.

 

 

Adjust of the Sub Shine (SBRT)

1. Insert a sign of color bar.

2. Enter in the Mode of SERVICE.

3. Adjust the CONTRAST and SHINE for the minimum.

4. Select SBRT with 1 and 4.

5. Adjust with 3 and 6 to obtain a weak visible bottom.

6. Write in the memory pressing MUTING later ENTER.

1.70 ± 0,05 VP-P

White

Black

SERVICE DISP 15

V2 V3

V4 V1

V. SIZE (VSIZ)

V. Center (VPOS)

 

Adjust of the SUB HUE, SUB COLOR (SHUE, SCOL)

1. Insert a sign of color bar.

2. Enter in the Mode of SERVICE.

3. Select the item DCOL and adjustment in the level " 0 ".

4. Connect the tip of the osciloscópio in the Placa C, CN301 Pin 7 (BLUE OUT).

5. Select SHUE and SCOL with 1 and 4.

6. Adjust with 3 and 6 for V1 = V4 ± 0.1 Vp-p (SCOL) and V2 = V3 ± 0.1 Vp-p (SHUE).

7. Reset the item DCOL for the level " 1 ".

8. Write in the memory pressing MUTING later ENTER.

 

Adjustment of the Size (VSIZ)

1. Insert a squared sign.

2. Enter in the Mode of SERVICE.

3. Select VSIZ with 1 and 4.

4. Adjust with 3 and 6 for the best vertical height.

 

Adjustment of the Vertical Position (VPOS)

1. Insert a squared sign.

2. Enter in the Mode of SERVICE.

3. Select VPOS with 1 and 4.

4. Adjust with 3 and 6 for the best vertical center.

5. Write in the memory pressing MUTING later ENTER.

H. Center (VPOS)

V CORRECTION (VSCO)

V CORRECTION (VSCO)

 

Adjustment of the Horizontal Position (HPOS)

1. Insert a squared sign.

2. Enter in the Mode of SERVICE.

3. Select HPOS with 1 and 4.

4. Adjust with 3 and 6 for the best horizontal center.

5. Write in the memory pressing MUTING later CENTER.

 

Vertical Linearidade (VLIN) and Vertical Correction

1. Insert a squared sign.

2. The vertical correction is adjusted automatically through the circuits and it should satisfy the conditions

below:

 

Memory of the Adjustment in the Mode of Service

 

1. Change DCOL for " 1 ".

2. After completing all the fittings, press " 0 " later ENTER.

Service Read

Read from Memory

Care: Don't turn off the feeding or CA immediately after pressing MUTING later ENTER.

Wait at least 10 seconds

Green 0

RED ENTER

 

Sony Model: KV-27XBR15 KV-27XBR50 KV-27HSR10 KV-32XVR35

Chassis: ANU-I FN

 

        1)Com the turned off television, press and maintain pressed the button of located service in the plate

back of connectors, while the apparel is tied by the remote control.

        2) to select the sub menus work the keys AUDIO it is VIDEO

        3) to select the items, press the keys 1 or 4

        4) to alter the values, press 3 or 6

        5) to save the alterations it Presses MUTE and Enter

        6) to leave, press POWER

 

Sony Model: KV-20M20 KV-20S20 KV-21RD1 KV-C2583

Chassis: BA3

With the turned off apparel it introduces the following sequence in the remote control: DISPLAY, 5, VOL+, POWER.

1 and 4 select the item.

3 and 6 alter the values.

Press MUTE and ENTER to save and POWER to leave.

 

Sony Model: KV 29EX

With the turned off apparel it Presses CANAL+ and CHANNEL simultaneously -, while it ties the equipment.

He/she will appear in the screen TT and introducing two numbers enters us sub menus. With UP / DOWN (+ / -) it selects him/it

item and with OK he/she enters in him.

With UP / DOWN (+ / -) it adjusts the value and with OK it saves.

 

Sony Model: KV 29PT50

With the turned off apparel it introduces the following sequence in the remote control: DISPLAY, 5, VOL+, POWER.

1 and 4 select the item.

3 and 6 alter the values.

Press MUTE and ENTER to save and POWER to leave.

Sony

With the turned off apparel it introduces the following sequence in the remote control: DISPLAY, 5, VOL+, POWER.

1 and 4 select the item.

3 and 6 alter the values.

Press MUTE and ENTER to save and POWER to leave.

 

Sony Model: European

Press the following sequence in CR: IT, 5, VOL+, TELETEXT OFF. He/she will appear TT in the screen. Press MENU for

to see the options.

 

Mode of Service of TV Tatung

Tatung Chassi: All

 
With the linked apparel, press the small key through a hole beside the key " MENU ". In the screen

Ityou appears the word ' VERSION ". With CH above and I lower if they change the meters and with VOL + / - the values.

Mode of Service of TV Telefunken

Telefunken Model: TK1499 TK2098 TK2099

 
To press the following sequence in the remote control: IMAGE, FACTORY, STAND-BY, MUTE, 1, 8, 2, POWER

ON. With VOL it adjusts the meter and with CHANNEL + / - the value. To leave it presses FACTORY or POWER

Telefunken Model: TK2078

 

To maintain tight the key MENU in the television and at the same time to press SETUP in the remote control. CHANNEL

+ / - they change the meters and VOL + / - the items. To leave and to save it presses SETUP.

 

Mode of Service of TV Thomson (Saba, Telefunken, Fergunson)

Thomson (Saba, Telefunken, Fergunson) Model: GY20TH

Chassis: ICC 17

 
To turn off the television in the main switch, to Press and to hold PR and VOL - for 8 seconds while it ties him/it

apparel. With PR + / - it selects the items and VOL + / - it adjusts the values. To leave temporarily it presses EXIT

in the remote control and to enter again it uses the blue key. To leave it places in stand-by or turn off.

Thomson (Saba, Telefunken, Fergunson) Model: TX 91

 

To turn off the television in the main switch and in the remote control to maintain tight the key VT AZUL while

it ties the apparel for 8 seconds. With PR + / - it selects the items and VOL + / - it adjusts the values. To leave

turn off the main switch.

Mode of Service of TV Toshiba

Toshiba Chassi: U15 MOD: 14P1495KM

With the linked tv; it presses the key mute, precione again and later press volume + and volume - simultaneously he/she leaves pressed until appearing the screen in the service Mode.

Mode of Service of TV Zenith

Zenith Chassi: All / Mode of Service GENERIC

        1)Turn on the television (POWER ON)

        2)Press the key MENU until appearing in the superior part of the screen a red picture

        3)Press in sequence :9;8;7;6 and ENTER

        4) to change of function it uses the keys

        5) to alter values it uses the numeric keyboard

        6) to save the alterations it presses the key ENTER

        7) to leave, press the key QUIT

Electric fittings for the remote control access method to the service Mode

the) - the television must it is linked (linked by the Power on)

b) - it Presses the following sequence of keys in the remote control:

order of 2 seconds (9, 8, 7, 6, and enter) she will open the service command oh and only to select what is

out of adjustment and to modify. We can make all the fittings of the apparel for this Mode. See Table to proceed.

To-018382-03 1, 69

00 FACT Mode 0 45 RGB CONT 49

01 Preset Px 0 46 Sub Color 80

02 Theater Px 0 47 Colr Dec 185

03 Love Px 0 48 Colr EnpH 76

04 SPORTS PX 0 49 YNR OFF R 2

05 DAYLGHT PX 0 50 YNR OFF TO 2

06 WEAKSIG PX 0 51 YNR ON 1

07 Vert Put 15 52 Y Enhace 2

08 Horiz Put 21 53 Hn Freq 163

09 Key Defeat 0 54 Vel Modul 3

10 CHAN LOCK 0 55 BLE GAIN 0

11 Min Vol 0 56 Pip Hpos 16

Table of the Model Zenith  SAR-2953BT

881-2 1,12

Preset Px Store

Aux Chnl on

Aux Bright 38

Brightness 50

Cap Phase 100

Vert Put 11

Horiz Put 31

Chan Lock off

Max Volum off

Min volum off

AC ON OFF

Key Deft off

Solemnity Prgm 2

CRT GLASS LITE

Seq Avail on

Text Mode on

SRch Dsply on

Wpl sw off

P/n gp off

Vert Phase 3

Horz Phase 14

Y MUTE OFF

Blk/Wht Sw off

Xtal Mode solemnity

Color sys solemnity

P/N ATTEN OFF

Xtal Srch 4V

AFC SW NORM

05/24/96-B

12 Max Vol 63 57 Pip SelDel 0

13 AC PWR ON 0 58 PIP YDEL 0

14 Av LocK 0 69 Pip Sw1 0

15 Feat Level 0 60 Pip Hsidel 2

16 BAND /AFC 0 61 PIP VSIDEL 0

17 Proj Mode 0 62 Pip Fry 5

18 BRIGHT RF 130 63 PIP VSPDEL 0